Flexible LED Wall Washers | Silicone Wall Washer

Choose Your Wall Washer

Five families — filter by the constraint you actually have

Pick the constraint on your drawing and the range narrows to the bodies that fit it. Full specs are on every card, no hovering needed.

Filter by

5 of 5 shown

IP67Ultra-slim

HL-WL2Q48

For reveals too shallow for anything else

HL-WL2Q48V24-Cxx · TPU + PU potting

Section: 18.5 × 9.5 mm
Saída: 1,919 lm/m
CRI: > 90
Bend Ø: 100 mm

18 W/mCut 125 mm115×50° option

View HL-WL2Q48

IP656 beam angles

HL-WL2620Pro

Pick the beam angle to suit the wall

HL-WL2620P-24V · silicone · PWM

Section: 26.5 × 20.5 mm
Saída: 1,480–1,580 lm/m
Beam: 15° – 20×55°
Bend Ø: 400 mm

24 W/mTunable whiteRGB / DMX512

View HL-WL2620Pro

IP65Silicone

HL-WL1616

Bends on the top face or the side face

HL-WL1616V24-Cxx · two-tone silicone

Section: 16 × 16 mm
Saída: 1,550–1,630 lm/m
CRI: 90
Bend Ø: 60 mm

16 W/mCut 20.83 mmUp to 10 m

View HL-WL1616

IP67DMX512

HL-WL13Q36

Addressable colour that turns a curve

HL-WL13Q36V24-DMX512 · TPU

Section: 18.5 × 9.5 mm
Saída: 230 / 770 lm/m
Controle: 6 px/m · 256 grey
Bend Ø: 100 mm

RGB 8.5 WRGBW 11.5 WCut 166.6 mm

View HL-WL13Q36

IP67RGBW

HL-WL13Q42

Colour at the lowest entry point

HL-WL13Q42V24-Crgb / Crgbw · TPU

Section: 18.5 × 9.5 mm
Saída: 264 / 540 lm/m
Beam: 40° / 30×45°
Bend Ø: 150 mm

RGB 6.2 WRGBW 8 WCut 166.6 mm

View HL-WL13Q42

Where Standard Wall Washers Fail

Four things go wrong on site — none of them are about wattage

Every wall-washing problem we are asked to fix comes down to one of these four.

PROBLEM 01

The wall is curved, the fixture is straight

A rigid extrusion is a straight line. On a radius you butt short lengths together and every joint reads as a dark break — exactly where the curve is most visible.

PROBLEM 02

The wash stops short of the top

Reach is set by beam angle, not power. Too wide and the wall is bright at the bottom and grey at the head; too narrow and you get a hot stripe.

PROBLEM 03

There is no room in the reveal

Deep bodies need a deep pocket. On a slim soffit, a window head or a joinery detail, a 20 mm-plus profile simply will not go in.

PROBLEM 04

Yellowing and water set the service life

UV turns cheap PVC opaque, and a body that is only shower-resistant fails in a drainage channel or under a pressure washer.

Problem → Solution

The same six problems, solved by number

Read down the middle column for what we do; read the right column for which family to specify.

On-site problem	What we do	The number to check	Specify
Joints show on a curved wall	Continuous bendable body — the run turns with the wall instead of being cut into chords	Bending Ø 60 / 100 / 150 / 400 mm	HL-WL1616 · HL-WL2Q48 · HL-WL13Q · HL-WL2620Pro
The wash does not reach the top	Beam angle selected from the wall height, backed by a published wash-height chart	6 angles, 15° to 20×55°	HL-WL2620Pro
No depth for the fixture	Ultra-slim body that still produces full wall-washing output	18.5 × 9.5 mm · 1,919 lm/m	HL-WL2Q48
Water ingress in a channel or under a hose	PU-potted TPU body, or one-piece silicone extrusion	IP67 / IP65	IP67: HL-WL2Q48 · HL-WL13Q36 · HL-WL13Q42
Scallops and dark bands on the wall	Optical lens, plus an asymmetric polarised option for wide, flat coverage	30°/45°/60°/20×45° · polarized 115×50°	HL-WL2Q48
A colour run has to follow the architecture	Addressable colour built into the same bendable body	DMX512 · 6 pixels/m · 256 grey levels	HL-WL13Q36 · HL-WL13Q42 · HL-WL2620Pro

Solutions by Application

Start from your project type

Find your wall below. Each one names the families that suit it and why.

Curved building facade at dusk, lit by a continuous linear wall washer

Curved facades & colonnades

The hardest case for a rigid washer, settled in a single run. No joints on the radius, no chord-cut gaps.

Bend Ø 100 mmIP671,919 lm/m

Continuous line of light under a building canopy washing the wall above

Soffits & canopies

Set the body in the soffit and let it graze the wall above. Six beam angles match the reach to the wall height.

6 beam angles400 mm bend Ø24 W/m

Textured stone feature wall lit evenly by a wall-washing light line

Interior feature walls

CRI 90 keeps stone, stucco and paint reading true. The slim body disappears into a shadow gap instead of sitting on the surface.

CRI 9016 W/m30° beam

Bar and lounge interior with continuous colour light lines along the walls and back bar

Reception, bar & retail colour lines

Colour runs and chases built into the wall line — addressable per pixel, following the curve without a visible joint.

DMX5126 px/mRGBW 770 lm/m

Corridor and stair wall lit by a continuous linear wall washer

Stair, corridor & handrail lines

Cut on site to match each flight. 5 m from one feed, or 10 m in total by feeding the middle of the HL-WL1616.

Cut 20.83 mmUp to 10 mIP65

Brick retaining wall in a courtyard, uplighted by an outdoor wall washer

Landscape & retaining walls

PU-potted TPU and one-piece silicone both resist salt, acid, alkali and UV — so a coastal installation does not yellow or craze.

Salt / UVIP65–IP67−25 ~ +45 °C

How to Choose

Four decisions, in this order

Work down the list. Most specification mistakes happen because the wall is chosen last.

Start with the wall

Wall height and the distance you can hold the body off the wall set the beam angle — and therefore the wash height.

Then the curve

Measure the tightest radius on the drawing. Minimum bending diameter is 60, 100, 150 or 400 mm.

Then the weather

IP65 for covered and shower-exposed positions; IP67 where the run sits in a channel or on a coastal elevation.

Then the function

Single colour, tunable white, RGB, RGBW or DMX512 — decided by what the operator changes after handover.

Wash Height, Published

How high will it actually wash?

Almost no one publishes this. On the HL-WL2620Pro, here is the wall-washing height for each beam angle at four mounting distances.

Beam angle	Body 300 mm from wall	200 mm	100 mm	50 mm
15°	800 mm	1,000 mm	1,400 mm	1,700 mm
30°	600 mm	900 mm	1,100 mm	1,300 mm
50°	550 mm	750 mm	900 mm	1,100 mm
18×20°	1,000 mm	1,300 mm	1,500 mm	1,800 mm

Measured with the body held at the stated distance from the wall. The narrower the beam, the higher the wash — and the closer the body, the higher it climbs. Every other family ships with its own chart, which we send with the quotation.

Fixing & Cutting

Four ways to fix it, and it cuts on site

OPTION 01

3M VHB tape

Red VHB backing for a smooth, prepared wall. Fastest route where the surface is flat and clean.

OPTION 02

Silicone clips

Clips that match the body colour, so the fixing disappears against the wall.

OPTION 03

Stainless steel clips

For coastal and high-wind elevations, or anywhere tape alone is not accepted.

OPTION 04

Aluminium profile + bracket

The angle can be set after installation, then locked — the most forgiving option on an uneven substrate.

Family	Section (W × H)	Cut unit on site	Max run from one feed	Body material
HL-WL1616	16 × 16 mm	20.83 mm	5 m — 10 m with a mid feed	Silicone
HL-WL2620Pro	26.5 × 20.5 mm	250 mm	5 m	Silicone
HL-WL2Q48	18.5 × 9.5 mm	125 mm	5 m	TPU + PU potting
HL-WL13Q42	18.5 × 9.5 mm	166.6 mm	5 m	TPU + PU potting
HL-WL13Q36	18.5 × 9.5 mm	166.6 mm	5 m	TPU

What You Get From Us

The other half of the solution is the service behind it

Layout & spacing

Send the wall height, length and finish. We return a fixture layout with the beam angle, the offset from the wall and the spacing between runs.

Samples before you commit

Pre-production samples for approval before mass production, so the wash and the finish are signed off on the real wall.

3-year warranty

Every wall washer family carries a 3-year warranty, across silicone and TPU bodies alike.

OEM & ODM

Custom length, colour temperature, CCT variants and control protocol — including end caps, connectors and clips to finish the run.

PERGUNTAS FREQUENTES

Flexible LED Wall Washers — Common Questions

How far from the wall should the fixture sit, and how high will it wash?

Both are set by the beam angle. On the HL-WL2620Pro a 30° beam reaches about 600 mm up the wall with the body 300 mm away, and about 1,300 mm when you move it in to 50 mm; the 15° beam reaches 1,700 mm at 50 mm. Each family ships with its own wash-height chart.

Can it follow a curved wall? What is the minimum bending diameter?

Yes — every family is a bendable silicone or TPU extrusion rather than a rigid fixture. Minimum bending diameter is 60 mm on the HL-WL1616, 100 mm on the HL-WL2Q48 and HL-WL13Q36, 150 mm on the HL-WL13Q42 and 400 mm on the HL-WL2620Pro.

Do I need IP65 or IP67?

IP65 (HL-WL1616, HL-WL2620Pro) is dust-tight and resists water jets. IP67 (HL-WL2Q48, HL-WL13Q36, HL-WL13Q42) adds tolerance to temporary immersion — specify it where a run sits in a drainage channel or gets hosed down. All five are DC24V and built for permanent outdoor installation.

Silicone or TPU — which one should I specify?

HL-WL1616 and HL-WL2620Pro use optical-grade silicone, which stays soft at low temperature and resists UV, salt, acid and alkali. HL-WL2Q48, HL-WL13Q36 and HL-WL13Q42 use TPU, chosen for yellowing resistance in a slimmer 18.5 × 9.5 mm section; the 2Q48 and 13Q42 bodies are PU-potted. Both are outdoor materials — the real choice is section size and bend radius.

How long a run can I feed from one end?

A single feed drives 5 m. On the HL-WL1616 you can reach 10 m in total by feeding the run from the middle — 5 m to each side. For longer elevations, plan a feed point roughly every 5 m.

Can I dim it, or run RGB, RGBW and DMX512?

The HL-WL2620Pro is PWM controlled and is available in single colour, tunable white (2700K + 6500K), RGB, RGBW and DMX512. The HL-WL13Q36 is DMX512-addressable at 6 pixels per metre with 256 grey levels — RGB at 8.5 W / 230 lm/m, or RGBW at 11.5 W / 770 lm/m. The HL-WL13Q42 comes as RGB (6.2 W / 264 lm/m) or RGBW (8 W / 540 lm/m).

How is it mounted, and can it be cut on site?

Four fixings are standard: 3M VHB tape, silicone clips, stainless steel clips, or an aluminium profile with rotatable brackets that let you set the angle after installation. Every body is cuttable on site — every 20.83 mm on the HL-WL1616, 125 mm on the HL-WL2Q48, 166.6 mm on the HL-WL13Q36 and HL-WL13Q42, and 250 mm on the HL-WL2620Pro.

What warranty, sample and MOQ terms do you offer?

Every wall washer family carries a 3-year warranty. Pre-production samples and volume pricing are available on request, and MOQ is set per SKU — tell us the project schedule and quantities and we will confirm both in writing.

Send us the wall, we will send back the layout

Wall height and length, the tightest radius on the drawing, whether it is indoor or exposed, and the finish. Our engineering team replies with a fixture layout, spacing and a factory-direct quotation.

Get a Layout & Quote Back to the Five Families

Flexível LED Wall Washer Solutions for Curved Facades, Soffits & Outdoor Walls