Ultra-Slim LED Profiles Where the constraint is height, not width
Two bodies, both built for the same problem: there is almost no depth. Outer heights from 8.2 mm, for ceilings and reveals where a standard section will not sit.
Three decisions decide whether this detail works
The channel is only part of it. What the run looks like in service depends on what it is fixed into, the section you choose and how the output is aimed.
Height is the whole specification
These bodies exist because the available depth is the binding constraint. Outer height starts at 8.2 mm; everything else follows from that.
Narrow strip, by necessity
A body this shallow takes 5–9 mm strip. That is the trade you make for the height.
Two bodies, two fixings
One recessed and one suspended — the two details where a shallow body is normally needed.
All 2 profiles in this group
Live from the product catalogue — add a profile in the backend and it appears here without touching this page.
Pick the constraint you actually have
Four of the decisions that come up first, each answered from the live range above — by outer height, by the strip you already buy, and by how the body has to be fixed.
How to narrow this range down to one body
Three numbers decide it, in this order. Every figure below is this group, not the whole catalogue.
Not the profile height: the space between the substrate and the finished plane, including the board thickness.
5–9 mm strip only. A wider strip cannot go into a body this shallow.
Shallow sections are less rigid, so long unsupported runs need the fixing spacing from the drawing.
Four ways this range fixes to a ceiling
Grouped by how the body is installed. Counts update from the catalogue index; each group links to the full mounting page.
Who builds the section, and what stands behind the drawing
The certifications below are issued to Shenzhen Helian Electronics Co., Ltd. Certificate numbers and the test standards are given in full, so any of them can be checked with the issuing body before you specify.
Management systems
ISO 9001:2015 & ISO 14001:2015
- Certificate
- 73025Q05190113R1S · 73025E05190046R1S
- Holder
- شركة Shenzhen Helian Electronics Co., Ltd.
- Scope
- R&D and sales of LED lighting fixtures (export)
- Issued
- 12 Jun 2025 — valid to 16 Jun 2028
- Body
- Shenzhen Zhonghuan International Certification Co., Ltd
CE — on the profile itself
LED PROFILE, EMC and LVD
- EMC cert.
- XDD04260780041502FDC
- EMC standard
- EN IEC 55015 · EN IEC 61547 · EN IEC 61000-3-2 · EN 61000-3-3
- LVD cert.
- XDD04260780041501FAC
- LVD standard
- EN IEC 60598-1:2024/A11:2024
- Issued
- 15 Apr 2026 · BST Testing (Shenzhen)
Material compliance
RoHS · REACH · diffuser
- Profile RoHS
- report TQT0780K01EC (IEC 62321 series)
- 6063 aluminium
- separate RoHS and REACH declarations
- PC diffuser
- SGS RoHS to EN / IEC 62321
- PMMA diffuser
- REACH SVHC declaration
Design rights
25 patent certificates
- Invention patent
- intelligent control method for luminaires
- Profile line light
- ZL 2018 2 1588485.0 · freely joinable
- Anti-glare line light
- ZL 2017 2 0569226.2
- Ceiling wall-washer
- utility model + design patent
- Also
- design patents and an EU design registration
- GATE 0%d Incoming material Incoming inspection standard and a receiving inspection record, per delivery.
- GATE 0%d First article First-article approval sheet held before a run is released.
- GATE 0%d Ageing & light-up A written ageing specification plus a batch ageing and light-up record.
- GATE 0%d Outgoing inspection Dedicated outgoing inspection reports for the extruded profile and for the diffuser.
What to send us, and what you get back
Most ceiling details are settled on the drawing, not on a phone call.
-
STEP 01
Send the ceiling detail
A section sketch, a photo of the reveal, or just the pocket depth and the strip you plan to use.
-
STEP 02
We match it to a section
We check the tooling we already run before proposing anything new — most details map onto an existing profile.
-
STEP 03
You get the drawing
The dimension drawing for the matched model, with W, H and the strip width it accepts, so you can check the cut-out.
-
STEP 04
Sample, then order
Cut lengths and finishing are confirmed against the drawing before anything goes to production.
What buyers ask before specifying this group
The questions that come up most often before a run is signed off.
What counts as ultra-slim here?
Outer height from 8.2 mm. This group is small on purpose: it is the section you reach for when a standard body will not go in.
Can it be recessed?
One of the two bodies is recessed and one is suspended. The recessed body still needs the cut-out depth shown on its drawing.
Will it take a normal strip?
No — 5–9 mm strip. If your strip is wider, the answer is a standard section and more depth, not a different ultra-slim body.
Why are there only two?
Because very few details genuinely need a body this shallow. If neither fits your reveal, send the section and we will say what the options are.
Is it the same as the mini range?
Different constraint. Mini is about outer width; ultra-slim is about outer height. Some details are limited by one and not the other.
Is a shallow body weaker in a long run?
There is less section to work with, so the fixing spacing matters more than on a deep body. Use the spacing on the drawing rather than assuming the standard one.
Why are there only two bodies here?
Because very few details genuinely need a body this shallow. If neither fits your reveal, send the section — at that point it is a tooling question, and we will say so.
Other ranges you may need on the same job
Most projects use more than one body. These are the ranges next to this one, plus the four mounting ranges.
Another range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeFlush in the board, trimless or flanged.
See the rangeHung from the slab on suspension.
See the rangeFixed onto a finished substrate.
See the rangeFor the junction where two surfaces meet.
See the rangeNext step
Send us the detail
Tell us where the run goes, the strip you plan to use and the length. We will come back with the section that fits and its drawing.