Outdoor & Waterproof LED Profiles Channels for exterior and wet-area runs
Exterior runs fail at the joints and the cover long before they fail at the extrusion. What separates an outdoor body from an indoor one is how the cover is held and how the ends close. 11 profiles in this group, strip widths 8–61 mm.
Three decisions decide whether this detail works
The channel is only part of it. What the run looks like in service depends on what it is fixed into, the section you choose and how the output is aimed.
The cover is the first thing water finds
An exterior body differs from an interior one in how the diffuser is retained and how the ends are closed — not in the aluminium section.
Joints are where a run leaks
Long exterior runs need connectors and end caps. The accessory list on each model shows what is available for the ends of that body.
Where the channel can hold water, it will
Section shape decides where water goes. A body with a place for it to sit is a body that will eventually sit in it.
All 11 profiles in this group
Direkt aus dem Produktkatalog – fügen Sie im Backend ein Profil hinzu, und es erscheint hier, ohne dass Sie diese Seite bearbeiten müssen.
Wähle die Einschränkung aus, die bei dir tatsächlich vorliegt
Vier der Entscheidungen, die als Erstes anfallen, werden jeweils anhand der obigen Auswahlmöglichkeiten beantwortet – nach Außenhöhe, nach dem bereits gekauften Streifen und danach, wie der Korpus befestigt werden muss.
How to narrow this range down to one body
Three numbers decide it, in this order. Every figure below is this group, not the whole catalogue.
Tell us where the run goes and what it is exposed to. That decides which body and which cover arrangement is used — the drawing then confirms it.
This group accepts 8–61 mm strip, which covers both single-row and wide exterior runs.
Surface, suspended and corner bodies are all here. On an exterior wall the fixing and the drainage at the fixing matter as much as the section.
Vier Möglichkeiten, wie sich dieser Herd an der Decke befestigen lässt
Gruppiert nach der Art der Montage. Die Zahlen werden aus dem Katalogindex aktualisiert; jede Gruppe enthält einen Link zur vollständigen Seite mit den Montageanleitungen.
Wer erstellt den Abschnitt, und was steckt hinter der Zeichnung?
Die nachstehend aufgeführten Zertifikate wurden an die Shenzhen Helian Electronics Co., Ltd. ausgestellt. Die Zertifikatsnummern und die Prüfnormen sind vollständig angegeben, sodass Sie jede davon vor Ihrer Bestellung bei der ausstellenden Stelle überprüfen können.
Managementsysteme
ISO 9001:2015 und ISO 14001:2015
- Zertifikat
- 73025Q05190113R1S · 73025E05190046R1S
- Halter
- Shenzhen Helian Electronics Co, Ltd
- Geltungsbereich
- Forschung und Entwicklung sowie Vertrieb von LED-Leuchten (Export)
- Ausgestellt
- 12. Juni 2025 – gültig bis zum 16. Juni 2028
- Hauptteil
- Shenzhen Zhonghuan International Certification Co., Ltd.
CE – auf dem Profil selbst
LED-Profil, EMV und LVD
- EMV-Zertifikat.
- XDD04260780041502FDC
- EMV-Norm
- EN IEC 55015 · EN IEC 61547 · EN IEC 61000-3-2 · EN 61000-3-3
- LVD-Zertifikat.
- XDD04260780041501FAC
- LVD-Norm
- EN IEC 60598-1:2024/A11:2024
- Ausgestellt
- 15. April 2026 · BST Testing (Shenzhen)
Einhaltung der Materialvorschriften
RoHS · REACH · Diffusor
- RoHS-Profil
- Bericht TQT0780K01EC (IEC-62321-Reihe)
- Aluminium 6063
- separate RoHS- und REACH-Erklärungen
- PC-Diffusor
- SGS RoHS gemäß EN / IEC 62321
- PMMA-Diffusor
- REACH-Erklärung zu besonders besorgniserregenden Stoffen (SVHC)
Geschmacksmusterrechte
25 Patenturkunden
- Erfindungspatent
- Intelligentes Steuerungsverfahren für Leuchten
- Profil-Lichtleiste
- ZL 2018 2 1588485.0 · freie Mitgliedschaft
- Blendfreies Linienlicht
- ZL 2017 2 0569226.2
- Decken-Wandfluter
- Gebrauchsmuster + Geschmacksmuster
- Außerdem
- Geschmacksmuster und eine EU-Geschmacksmustereintragung
- GATE 0%d Eingehendes Material Norm für die Wareneingangskontrolle und ein Wareneingangsprotokoll pro Lieferung.
- GATE 0%d Erster Artikel Freigabeblatt für das Erstmuster, das vor der Freigabe einer Serie vorgelegt wird.
- GATE 0%d Alterung & Beleuchtung Eine schriftliche Alterungsspezifikation sowie ein Protokoll über die Alterung der Charge und die Inbetriebnahme.
- GATE 0%d Ausgangskontrolle Spezielle Ausgangskontrollberichte für das stranggepresste Profil und für den Diffusor.






Was Sie uns schicken sollen und was Sie dafür erhalten
Die meisten Details zur Decke werden in der Zeichnung festgelegt, nicht am Telefon.
-
SCHRITT 01
Senden Sie die Deckenzeichnung
Eine Schnittskizze, ein Foto der Freilegung oder einfach nur die Taschentiefe und der Streifen, den Sie verwenden möchten.
-
SCHRITT 02
Wir ordnen es einem Abschnitt zu
Bevor wir etwas Neues vorschlagen, prüfen wir zunächst die bereits eingesetzten Werkzeuge – die meisten Details lassen sich einem bestehenden Profil zuordnen.
-
SCHRITT 03
Du bekommst die Zeichnung
Die Maßzeichnung für das passende Modell mit den Maßen W, H und der zulässigen Streifenbreite, damit Sie den Ausschnitt überprüfen können.
-
SCHRITT 04
Erst probieren, dann bestellen
Die Schnittlängen und die Endbearbeitung werden anhand der Zeichnung überprüft, bevor die Produktion beginnt.
What buyers ask before specifying this group
The questions that come up most often before a run is signed off.
Are these profiles IP rated?
The aluminium section on its own is not what carries an IP rating — the rating belongs to the assembled fixture, with its cover, gaskets and end caps. Tell us the location and we will say which body and which accessories that duty calls for.
Can I use an indoor profile outside?
No. Start from this group: the cover retention and the end treatment are the parts that change, and they are the parts that fail first.
Do I need a gasket?
It depends on the body and the cover. What each channel takes is listed on its specification sheet, which is linked from every card above.
How are long runs joined?
With connectors sized for the section, listed per model. Exterior joints are the detail worth confirming on the drawing before you order.
What about a pool or a fountain?
Tell us the exposure and we will say which body is used for it. The requirement comes from the project, not from a generic rating on this page.
Do the end caps affect the sealing?
Yes — the ends are part of the assembly, not an afterthought. What each body takes at the ends is listed on its specification sheet, which is linked from every card.
What about salt air or a swimming pool?
Tell us the exposure and we will say which body is used for it. The requirement comes from the project, not from a generic claim on a page.
Other ranges you may need on the same job
Most projects use more than one body. These are the ranges next to this one, plus the four mounting ranges.
Another range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeAnother range that often appears on the same drawing.
See the rangeFlush in the board, trimless or flanged.
See the rangeHung from the slab on suspension.
See the rangeFixed onto a finished substrate.
See the rangeFor the junction where two surfaces meet.
See the rangeNächster Schritt
Send us the detail
Tell us where the run goes, the strip you plan to use and the length. We will come back with the section that fits and its drawing.